If you have tested the mixer by spinning the drum and it still does not run it could mean that the switch is broken or not working properly. In this case it is worth testing the switch to see if it needs replacing before moving to other more costly parts of the machine. Gearbox a new switch eh, i think it will be the wiring. there could be a break within the coloured sleeving of the cable? The Belle Minimix 150 is a common mixer used for construction projects across the UK. The mixer hasn't changed substantially since it first went into production. However, as with all working machines that are in constant use, you may from time to time encounter issues. Correctly identifying the problem can save time and money when repairing these mixers.

they just came out of nowhere and took me up to their craft, where i was experimented on sexually..........." e. Mix: Let the mixer run until your materials are thoroughly mixed, then turn off the power switch. b. Examine the Switch: The switch may be worn or damaged. If it can't hold in the "on" position, consider replacing it. Over time the belt can wear down and eventually snap. If you find your motor is running but the drum isn’t rotating, it’s likely that the belt has broken. This is very common and is simply caused by lots of use. Whether your mixer is electric powered, or petrol powered, you can remove the side cover on the machine and replace the belt with ease. Broken Fan Minimix 150 (04/2002 - 04/2007), Minimix 130, Maxi 140, Minimix 140, BWE40, BWE60, MiniAlpha, Minimix 110, Minimix 80, Minimix 60LLP, if i read this thread write he went off to the mixer at 18.29pm with the diagram and had not returned at 02.33am? If your Belle Minimix 150 runs when it is first switched on, it suggests that the switch and the capacitor are working. A common cause for the machines to stop running at this point could be that the motor fan is broken or missing blades. This fan is designed to take the warm air away from the motor, so with this element damaged after a few minutes of running the motor can overheat and shut down. These fans are available separately. Blown Capacitor brown and red come out of a loom together, they go to the capacitor. does not show which one goes to which side on the diagram.

i have a 110 volt mixer but it is late and dark (ish) I will take a look tomorrow and post here what I find. Thanks for all that. When he got the mixer it would work if you held the switch in with your finger, so it was working. The wiring seems to be correct, thanks to your advice. c. Drum Obstructions: Foreign objects or excessive material buildup inside the drum can impede its rotation. Empty the drum, remove any obstructions, and clean it thoroughly.

Minimix Manuals

b. Remove the Old Switch: Typically, the switch is located on the control panel. Unscrew or unclip the old switch and carefully disconnect the wires. We hope you found our common troubleshooting tips helpful. Please note that although the tips above can be used they will not always fix the problem, as every machine and problem has different factors attached to it.

c. Belt or Pulley Problems: Examine the drive belt and pulleys for wear and tear. A damaged or loose belt can prevent the drum from turning. Replace any damaged components. If your Belle mixer starts and then stops unexpectedly during operation, consider these potential causes:Holding the start button for too long can blow the capacitor. If the mixer won't start and you can't hear a buzz when you press the start button, it could be either the switch or the capacitor. A simple way to identify what is causing the problem is to try spinning the drum in the direction it should turn whilst pressing the start button. If the mixer then starts, this will indicate that the capacitor is no longer working and needs replacing. Broken Switch Here is a troubleshooting guide to help fix a Belle Minimix 150 cement mixer that won't start or runs with low power: you can just see the headlines - man goes to garage and disappears for unexplained amount of hours.... Many, many thanks SG. I have printed this off for him and he is away to the garage with it........... hexagonal fitting at top. below that to the right is a single termianl - A1. then below that 4 terminals arranged as 2 rows of 2.